Código de avería P0014: This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles, including but not limited to Toyota, VW, Honda, Chevrolet, Hyundai, Audi, Acura, etc. A P0014 code refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car’s PCM (powertrain control module) or ECM (engine control module). VVT is a technology used in the engine to allow it to get greater power or efficiency at different running points. That consists of a few different components but the P0014 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is above a set limit (over-advanced), the engine light will be illluminated and the code will be set. Bank 1 is the side of the engine containing cylinder #1. The "B" camshaft shall be either the "exhaust," "right," or "rear" camshaft. Left/Right and Front/Rear are determined as if viewed from the driver’s seating position.
codigo-p0014
Código de avería P0015: This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles, including but not limited to Toyota, VW, Honda, Ford, Chevrolet, Hyundai, Audi, Acura, etc. A code P0015 refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car’s PCM (powertrain control module, also called an ECM). That consists of a few different components but the P0015 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is over-retarded, the engine light will be illluminated and the code will be set. Bank #1 is the side of the engine that contains cylinder #1. The "B" camshaft shall be either the "exhaust," "right," or "rear" camshaft. Left/Right and Front/Rear are determined as if viewed from the driver’s seating position.
codigo-p0015
Código de avería P0016: This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles, including but not limited to Ford, Dodge, Toyota, VW, Honda, Chevrolet, Hyundai, Audi, Acura, etc. The crankshaft position sensor (CKP) and Camshaft position sensor (CMP) work in harmony to control the spark/fuel delivery and timing. They both consist of a reluctor, or tone, ring which passes over a magnetic sensor, which generates a voltage, indicating position.
codigo-p0016
Código de avería P0017: This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles, including but not limited to Ford, Dodge, Toyota, VW, Honda, Chevrolet, Hyundai, Audi, Acura, etc. The crankshaft position sensor (CKP) and Camshaft position sensor (CMP) work in harmony to control the spark/fuel delivery and timing. They both consist of a reluctor, or tone, ring which passes over a magnetic sensor, which generates a voltage, indicating position. The crankshaft sensor is part of the primary ignition system and functions as the «trigger». It detects the position of the crankshaft relays that information on to the PCM or the ignition module (depending on the vehicle) to control spark timing. The Camshaft position sensor detects the position of the camshafts and relays the information to the PCM. The PCM uses the CMP signal to identify the beginning of the injector sequence. What ties these two shafts and their sensors together is the timing belt or chain. The cam and crank should be precisely timed together. If the PCM detects that the crank and cam signals are out of time by a specific number of degrees, this DTC will set. Bank 1 is the side of the engine that contains cylinder #1, the "B" sensor is most likely the exhaust camshaft side. Note it is not uncommon on certain models to see this DTC in conjuction with P0008, P0009, P0016, P0018, and P0019. If you have a GM vehicle and have those multiple DTCs, check for service bulletins that may apply to your engine.
codigo-p0017
Código de avería P0018: This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles, including but not limited to Ford, Dodge, Toyota, VW, Honda, Chevrolet, Hyundai, Audi, Acura, etc. The crankshaft position sensor (CKP) and Camshaft position sensor (CMP) work in harmony to control the spark/fuel delivery and timing. They both consist of a reluctor, or tone, ring which passes over a magnetic sensor, which generates a voltage, indicating position. The crankshaft sensor is part of the primary ignition system and functions as the «trigger». It detects the position of the crankshaft relays that information on to the PCM or the ignition module (depending on the vehicle) to control spark timing. The Camshaft position sensor detects the position of the camshafts and relays the information to the PCM. The PCM uses the CMP signal to identify the beginning of the injector sequence. What ties these two shafts and their sensors together is the timing belt or chain. The cam and crank should be precisely timed together. If the PCM detects that the crank and cam signals are out of time by a specific number of degrees, this DTC will set. Bank 2 is the side of the engine that doesn’t contains cylinder #1, the "A" sensor is most likely the intake camshaft side. Note it is not uncommon on certain models to see this DTC in conjuction with P0008, P0009, P0016, P0017, and P0019. If you have a GM vehicle and have those multiple DTCs, check for service bulletins that may apply to your engine.
codigo-p0018
Código de avería P0019: This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles, including but not limited to Ford, Dodge, Toyota, VW, Honda, Chevrolet, Hyundai, Audi, Acura, etc. The crankshaft position sensor (CKP) and Camshaft position sensor (CMP) work in harmony to control the spark/fuel delivery and timing. They both consist of a reluctor, or tone, ring which passes over a magnetic sensor, which generates a voltage, indicating position. The crankshaft sensor is part of the primary ignition system and functions as the «trigger». It detects the position of the crankshaft relays that information on to the PCM or the ignition module (depending on the vehicle) to control spark timing. The Camshaft position sensor detects the position of the camshafts and relays the information to the PCM. The PCM uses the CMP signal to identify the beginning of the injector sequence. What ties these two shafts and their sensors together is the timing belt or chain. The cam and crank should be precisely timed together. If the PCM detects that the crank and cam signals are out of time by a specific number of degrees, this DTC will set. Bank 2 is the side of the engine that contains cylinder #1, the "B" sensor is most likely the exhaust camshaft side. Note it is not uncommon on certain models to see this DTC in conjuction with P0008, P0009, P0016, P0017, and P0018. If you have a GM vehicle and have those multiple DTCs, check for service bulletins that may apply to your engine.
codigo-p0019
Código de avería P001A: This is a generic powertrain diagnostic trouble code (DTC) and typically applies to OBD-II vehicles. Vehicles affected may include but is not limited to Volvo, Chevrolet, Ford, Dodge, Porsche, Ford, Land Rover, Audi, Hyundai, Fiat, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration. The camshaft is responsible for the valves’ positions. It uses a shaft with lobes integrated in the design to a specific measurement (depending on engine manufacturer and model) to, when mechanically timed properly, precisely open and close valves at the optimal amount/speed. The crankshaft and camshaft are connected mechanically using different styles (e.g. belt, chain). In the code description, they mention the camshaft "profile". What they are referring to here, is the shape or the roundness of the lobe. Some systems use these adjustable lobes, I am going to call it, to precisely integrate a more efficient "lobe design" at given times. These are beneficial because, at different engine speeds and loads, having a different camshaft profile can increase volumetric efficiency among other benefits depending on operator demands. It is important to note, most times it is not another physical lobe rather, manufacturers mimic a "new lobe" by using varying strategies (i.e. switchable/adjustable rocker arm components). The letter "1" in the description is extremely valuable in this case. Not only could the camshaft be on either side, but there may be 2 shafts on each cylinder head. So it’s important to clarify which camshaft you are working with before proceeding. As far as banks go, bank 1 will be the one with cylinder #1. Most times, B refers to the exhaust camshaft and A refers to the intake camshaft. This all depends on which particular engine you are working with as there are countless different designs that will alter these diagnosis procedures depending which one you own. Refer to she manufacturer’s service manual for the specifics. The ECM (Engine Control Module) illuminates the CEL (Check Engine Light) with P001A and related codes when it detects a malfunction within the camshaft profile control circuit. P001A is set when there is an open within the bank 1 circuit.
codigo-p001a
Código de avería P001B: This is a generic powertrain diagnostic trouble code (DTC) and typically applies to OBD-II vehicles. Vehicles affected may include but is not limited to Volvo, Chevrolet, Ford, Dodge, Porsche, Ford, Land Rover, Audi, Hyundai, Fiat, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration. The camshaft is responsible for the valves’ positions. It uses a shaft with lobes integrated in the design to a specific measurement (depending on engine manufacturer and model) to, when mechanically timed properly, precisely open and close valves at the optimal amount/speed. The crankshaft and camshaft are connected mechanically using different styles (e.g. belt, chain). In the code description, they mention the camshaft "profile". What they are referring to here, is the shape or the roundness of the lobe. Some systems use these adjustable lobes, I am going to call it, to precisely integrate a more efficient "lobe design" at given times. These are beneficial because, at different engine speeds and loads, having a different camshaft profile can increase volumetric efficiency among other benefits depending on operator demands. It is important to note, most times it is not another physical lobe rather, manufacturers mimic a "new lobe" by using varying strategies (i.e. switchable/adjustable rocker arm components). The letter "1" in the description is extremely valuable in this case. Not only could the camshaft be on either side, but there may be 2 shafts on each cylinder head. So it’s important to clarify which camshaft you are working with before proceeding. As far as banks go, bank 1 will be the one with cylinder #1. Most times, B refers to the exhaust camshaft and A refers to the intake camshaft. This all depends on which particular engine you are working with as there are countless different designs that will alter these diagnosis procedures depending which one you own. Refer to she manufacturer’s service manual for the specifics. The ECM (Engine Control Module) illuminates the CEL (Check Engine Light) with P001B and related codes when it detects a malfunction within the camshaft profile control circuit. P001B is set when there is an low electrical condition within the bank 1 circuit.
codigo-p001b
Código de avería P001C: This is a generic powertrain diagnostic trouble code (DTC) and typically applies to OBD-II vehicles. Vehicles affected may include but is not limited to Volvo, Chevrolet, Ford, Dodge, Porsche, Ford, Land Rover, Audi, Hyundai, Fiat, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration. The camshaft is responsible for the valves’ positions. It uses a shaft with lobes integrated in the design to a specific measurement (depending on engine manufacturer and model) to, when mechanically timed properly, precisely open and close valves at the optimal amount/speed. The crankshaft and camshaft are connected mechanically using different styles (e.g. belt, chain). In the code description, they mention the camshaft "profile". What they are referring to here, is the shape or the roundness of the lobe. Some systems use these adjustable lobes, I am going to call it, to precisely integrate a more efficient "lobe design" at given times. These are beneficial because, at different engine speeds and loads, having a different camshaft profile can increase volumetric efficiency among other benefits depending on operator demands. It is important to note, most times it is not another physical lobe rather, manufacturers mimic a "new lobe" by using varying strategies (i.e. switchable/adjustable rocker arm components). The letter "1" in the description is extremely valuable in this case. Not only could the camshaft be on either side, but there may be 2 shafts on each cylinder head. So it’s important to clarify which camshaft you are working with before proceeding. As far as banks go, bank 1 will be the one with cylinder #1. Most times, B refers to the exhaust camshaft and A refers to the intake camshaft. This all depends on which particular engine you are working with as there are countless different designs that will alter these diagnosis procedures depending which one you own. Refer to she manufacturer’s service manual for the specifics. The ECM (Engine Control Module) illuminates the CEL (Check Engine Light) with P001C and related codes when it detects a malfunction within the camshaft profile control circuit. P001C is set when there is an high electrical condition within the bank 1 circuit.
codigo-p001c
Código de avería P001D: This is a generic powertrain diagnostic trouble code (DTC) and typically applies to OBD-II vehicles. Vehicles affected may include but is not limited to Volvo, Chevrolet, Ford, Dodge, Porsche, Ford, Land Rover, Audi, Hyundai, Fiat, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration. The camshaft is responsible for the valves’ positions. It uses a shaft with lobes integrated in the design to a specific measurement (depending on engine manufacturer and model) to, when mechanically timed properly, precisely open and close valves at the optimal amount/speed. The crankshaft and camshaft are connected mechanically using different styles (e.g. belt, chain). In the code description, they mention the camshaft "profile". What they are referring to here, is the shape or the roundness of the lobe. Some systems use these adjustable lobes, I am going to call it, to precisely integrate a more efficient "lobe design" at given times. These are beneficial because, at different engine speeds and loads, having a different camshaft profile can increase volumetric efficiency among other benefits depending on operator demands. It is important to note, most times it is not another physical lobe rather, manufacturers mimic a "new lobe" by using varying strategies (i.e. switchable/adjustable rocker arm components). The letter "2" in the description is extremely valuable in this case. Not only could the camshaft be on either side, but there may be 2 shafts on each cylinder head. So it’s important to clarify which camshaft you are working with before proceeding. As far as banks go, bank 1 will be the one with cylinder #1. Most times, B refers to the exhaust camshaft and A refers to the intake camshaft. This all depends on which particular engine you are working with as there are countless different designs that will alter these diagnosis procedures depending which one you own. Refer to she manufacturer’s service manual for the specifics. The ECM (Engine Control Module) illuminates the CEL (Check Engine Light) with P001D and related codes when it detects a malfunction within the camshaft profile control circuit. P001D is set when there is an open within the bank 2 circuit.
codigo-p001d